How do you cut Skatelite?

Use a thinner kerfed (skinny) - carbide tipped blade for cutting the ramp surfacing and make sure it is very sharp! You don't need to tape the cut line if your blade is sharp and the blade depth is set just a little deeper than 1/4". Since this ramp surfacing is very expensive, make sure your measurements are accurate.

How do you use Skatelite?

Cut a plastic straw in half at a 45° angle. Put a little silicon around the square end of the straw, and insert the straw through the hole until the square end is flush with the surface. The silicon will hold it in place, and the angled bottom end will allow the water to drain. A note about moisture.

Do you need to paint Skatelite?

Made with paper that is either post consumer waste recycled or sustainably harvested rapidly renewable paper, Skatelite can be used raw or can be painted, custom printed or customised with vinyls. It's also an excellent for making Longboard decks.

What is Skatelite made of?

Skatelite products are made from a super-durable paper-composite material that is designed to stand up to the daily punishment inflicted by skateboards and BMX bikes.

Is Skatelite waterproof?

Fast and super strong, professional grade Skatelite Pro is the supreme riding surface for outdoor skateparks and backyard ramps. The solid material is weatherproof and withstands the constant punishment inflicted by determined riders.

Does OC Ramps use Skatelite?

Pre-Drill Option: Get your Skatelite pre-drilled and countersunk, for a small convenience fee. This special option is only valid for OC Ramps products (sorry DIY ramp builders). It takes the additional headache and hours of drilling away for a small convenience fee.

How much does a sheet of Skatelite weigh?

Skatelite comes in three colors: maple, brown, and black. The black Skatelite is made to absorb little or no heat, so it can be used outside. Sheets are available in the standard four-by-eight-foot sizes, and each weigh 50 pounds.

What is the best plywood for skate ramps?

The quality of wood dictates how strong and durable the plywood is. For instance, birch has phenomenal surface hardness, therefore birch plywood is one of the best. And a great choice as the riding surface for many indoor ramps.

How do you waterproof a skate ramp?

The standard way to waterproof your ramp is to paint it using a paint designed specifically for use on skate ramps. Coating your deck with paint protects it from various weather conditions such as heat, humidity and sunlight, as well as rain.

Is plywood good for skating?

We recommend using any type of smooth and sanded plywood. Particle board is quite possibly the worst type of wood you could use! A halfpipe outdoors with plywood will need something such as Skatepaint to help protect the wood from rain/snow.

What do you seal a skate ramp with?

Two types of paints that work well for this is Spar Urethane and Polyurethane Paint. In addition to painting the ramp, a giant tarp is also a good idea, the last thing you want is water pooling up on your ramp (painted or not).

How thick should plywood be for skate ramp?

For covering the ramp face, we're going to use two layers of 3/8" thick plywood and then a final layer of 1/8" on top. Start by pushing a sheet of 3/8" tight against the coping and screwing it down to the 2x4s below. Repeat it all the way across the ramp, making cuts as needed until the entire thing is covered.

How do you bend plywood for a ramp?

Heat the plywood, using your hands to put pressure on it and bend it. Once the wood is bent to the right shape, lay it into your mold and clamp it in place. Then soak towels in water and heat them in the microwave or dip them in boiling water. Lay them on the workpiece and clamp the whole thing together.

Can I waterproof Masonite?

To avoid structural failure of a piece of installed Masonite, you need to waterproof the surface of the Masonite after installation. Lacquer-based waterproofing systems bond to the surface of the Masonite and provide adequate protection against moisture intrusion.

Can you paint over Skatepaint?

If you'd like, you can apply a colored (flat) latex paint over the Skatepaint after its cured. This you can buy from any hardware store.

Can I use plywood for a wheelchair ramp?

Can I use plywood for a wheelchair ramp? For an indoor ramp, plywood might work, but when building a wheelchair ramp outdoors, use pressure-treated lumber.

What is a good angle for a skateboard ramp?

One of the most basic types of skateboard ramps are kickers. They essentially consist of a bank or slope at a straight angle. Relative to the ground, a kicker ramp's surface is typically banked at about 15-30 degrees. There is no curvature to the slope.

What is SkateSeal?

SkateSeal is a premium quality protective coating specifically formulated for timber skate ramps. SkateSeal was developed for skateboarding with just the perfect amount of grip & slip. SkateSeal provides a hard & fast surface with awesome feel under wheel & will protects your ramp from the elements.

What is ramp armor made of?

Unlike the other guys out there, Ramp Armor is more affordably priced and lasts just as long while riding just as good, if not better. Made with high-quality materials and 100% cotton.

Can you move a half pipe?

You could always take out the center plank and cut the framing if need be, then put it back together with large gusset plates on each side of the new joints. That would probably work. If it is 6' at the peaks, you should be able to lay it on it's side and transport it on a 12' trailer.

How long does it take for OC ramps to ship?

How long will it take for me to receive my order? If you ordered one of our smaller ramp kits, our turnaround time is approximately 1 - 2 weeks. If you ordered one of our larger ramp kits, our turnaround time is approximately 3 - 4 weeks.

How long do you soak wood to bend it?

They have to soak the wood in water to bend it and get it into a certain shape. To efficiently make the wood bendable, it's recommended that you soak the wood in relatively hot water for one to three hours. Many other factors can change this, but one to three hours will work for most wood types.

Can you soak plywood to bend it?

Step 2: Soak the Plywood

Apply towels or rags saturated with warm water to the crease line and the parts of the plywood that will be under stress. If possible, apply the rags on both sides of the sheet. It could take several days for the plywood to become soft enough to bend.